/
usr
/
src
/
linux-headers-5.15.0-181
/
drivers
/
phy
/
ti
/
/usr/src/linux-headers-5.15.0-181/drivers/phy/ti
mkdir
upload
Name
Size
Mode
Actions
Kconfig
3489
0644
edit
dl
rm
Makefile
520
0644
edit
dl
rm
Edit:
/usr/src/linux-headers-5.15.0-181/drivers/phy/ti/Kconfig
(3489B)
# SPDX-License-Identifier: GPL-2.0-only # # Phy drivers for TI platforms # config PHY_DA8XX_USB tristate "TI DA8xx USB PHY Driver" depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST select GENERIC_PHY select MFD_SYSCON help Enable this to support the USB PHY on DA8xx SoCs. This driver controls both the USB 1.1 PHY and the USB 2.0 PHY. config PHY_DM816X_USB tristate "TI dm816x USB PHY driver" depends on ARCH_OMAP2PLUS || COMPILE_TEST depends on USB_SUPPORT select GENERIC_PHY select USB_PHY help Enable this for dm816x USB to work. config PHY_AM654_SERDES tristate "TI AM654 SERDES support" depends on OF && (ARCH_K3 || COMPILE_TEST) depends on COMMON_CLK select GENERIC_PHY select MULTIPLEXER select REGMAP_MMIO select MUX_MMIO help This option enables support for TI AM654 SerDes PHY used for PCIe. config PHY_J721E_WIZ tristate "TI J721E WIZ (SERDES Wrapper) support" depends on OF && (ARCH_K3 || COMPILE_TEST) depends on HAS_IOMEM && OF_ADDRESS depends on COMMON_CLK select GENERIC_PHY select MULTIPLEXER select REGMAP_MMIO select MUX_MMIO help This option enables support for WIZ module present in TI's J721E SoC. WIZ is a serdes wrapper used to configure some of the input signals to the SERDES (Sierra/Torrent). This driver configures three clock selects (pll0, pll1, dig) and resets for each of the lanes. config OMAP_CONTROL_PHY tristate "OMAP CONTROL PHY Driver" depends on ARCH_OMAP2PLUS || COMPILE_TEST help Enable this to add support for the PHY part present in the control module. This driver has API to power on the USB2 PHY and to write to the mailbox. The mailbox is present only in omap4 and the register to power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an additional register to power on USB3 PHY/SATA PHY/PCIE PHY (PIPE3 PHY). config OMAP_USB2 tristate "OMAP USB2 PHY Driver" depends on ARCH_OMAP2PLUS || ARCH_K3 depends on USB_SUPPORT select GENERIC_PHY select USB_PHY select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST help Enable this to support the transceiver that is part of SOC. This driver takes care of all the PHY functionality apart from comparator. The USB OTG controller communicates with the comparator using this driver. config TI_PIPE3 tristate "TI PIPE3 PHY Driver" depends on ARCH_OMAP2PLUS || COMPILE_TEST select GENERIC_PHY select OMAP_CONTROL_PHY help Enable this to support the PIPE3 PHY that is part of TI SOCs. This driver takes care of all the PHY functionality apart from comparator. This driver interacts with the "OMAP Control PHY Driver" to power on/off the PHY. config PHY_TUSB1210 tristate "TI TUSB1210 ULPI PHY module" depends on USB_ULPI_BUS select GENERIC_PHY help Support for TI TUSB1210 USB ULPI PHY. config TWL4030_USB tristate "TWL4030 USB Transceiver Driver" depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS depends on USB_SUPPORT depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y' select GENERIC_PHY select USB_PHY help Enable this to support the USB OTG transceiver on TWL4030 family chips (including the TWL5030 and TPS659x0 devices). This transceiver supports high and full speed devices plus, in host mode, low speed. config PHY_TI_GMII_SEL tristate select GENERIC_PHY select REGMAP help This driver supports configuring of the TI CPSW Port mode depending on the Ethernet PHY connected to the CPSW Port.
Save
cmd:
run