/
usr
/
src
/
linux-headers-5.15.0-190
/
arch
/
arm
/
plat-omap
/
/usr/src/linux-headers-5.15.0-190/arch/arm/plat-omap
mkdir
upload
Name
Size
Mode
Actions
include/
-
0755
rm
Kconfig
3822
0644
edit
dl
rm
Makefile
310
0644
edit
dl
rm
Edit:
/usr/src/linux-headers-5.15.0-190/arch/arm/plat-omap/Kconfig
(3822B)
# SPDX-License-Identifier: GPL-2.0 config ARCH_OMAP bool if ARCH_OMAP menu "TI OMAP Common Features" config ARCH_OMAP_OTG bool comment "OMAP Feature Selections" config OMAP_DEBUG_DEVICES bool help For debug cards on TI reference boards. config OMAP_DEBUG_LEDS def_bool y if NEW_LEDS depends on OMAP_DEBUG_DEVICES select LEDS_CLASS config POWER_AVS_OMAP bool "AVS(Adaptive Voltage Scaling) support for OMAP IP versions 1&2" depends on (ARCH_OMAP3 || ARCH_OMAP4) && PM select POWER_SUPPLY help Say Y to enable AVS(Adaptive Voltage Scaling) support on OMAP containing the version 1 or version 2 of the SmartReflex IP. V1 is the 65nm version used in OMAP3430. V2 is the update for the 45nm version of the IP used in OMAP3630 and OMAP4430 Please note, that by default SmartReflex is only initialized and not enabled. To enable the automatic voltage compensation for vdd mpu and vdd core from user space, user must write 1 to /debug/smartreflex/sr_<X>/autocomp, where X is mpu_iva or core for OMAP3. Optionally autocompensation can be enabled in the kernel by default during system init via the enable_on_init flag which an be passed as platform data to the smartreflex driver. config POWER_AVS_OMAP_CLASS3 bool "Class 3 mode of Smartreflex Implementation" depends on POWER_AVS_OMAP && TWL4030_CORE help Say Y to enable Class 3 implementation of Smartreflex Class 3 implementation of Smartreflex employs continuous hardware voltage calibration. config OMAP_RESET_CLOCKS bool "Reset unused clocks during boot" depends on ARCH_OMAP help Say Y if you want to reset unused clocks during boot. This option saves power, but assumes all drivers are using the clock framework. Broken drivers that do not yet use clock framework may not work with this option. If you are booting from another operating system, you probably do not want this option enabled until your device drivers work properly. config OMAP_MPU_TIMER bool "Use mpu timer" depends on ARCH_OMAP1 help Select this option if you want to use the OMAP mpu timer. This timer provides more intra-tick resolution than the 32KHz timer, but consumes more power. config OMAP_32K_TIMER bool "Use 32KHz timer" depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS default y if (ARCH_OMAP16XX || ARCH_OMAP2PLUS) help Select this option if you want to enable the OMAP 32KHz timer. This timer saves power compared to the OMAP_MPU_TIMER, and has support for no tick during idle. The 32KHz timer provides less intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is currently only available for OMAP16XX, 24XX, 34XX, OMAP4/5 and DRA7XX. On OMAP2PLUS this value is only used for CONFIG_HZ and CLOCK_TICK_RATE compile time calculation. The actual timer selection is done in the board file through the (DT_)MACHINE_START structure. config OMAP3_L2_AUX_SECURE_SAVE_RESTORE bool "OMAP3 HS/EMU save and restore for L2 AUX control register" depends on ARCH_OMAP3 && PM help Without this option, L2 Auxiliary control register contents are lost during off-mode entry on HS/EMU devices. This feature requires support from PPA / boot-loader in HS/EMU devices, which currently does not exist by default. config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID int "Service ID for the support routine to set L2 AUX control" depends on OMAP3_L2_AUX_SECURE_SAVE_RESTORE default 43 help PPA routine service ID for setting L2 auxiliary control register. config OMAP_SERIAL_WAKE bool "Enable wake-up events for serial ports" depends on ARCH_OMAP1 && OMAP_MUX default y help Select this option if you want to have your system wake up to data on the serial RX line. This allows you to wake the system from serial console. endmenu endif
Save
cmd:
run