/
usr
/
src
/
linux-headers-5.15.0-190
/
arch
/
nios2
/
platform
/
/usr/src/linux-headers-5.15.0-190/arch/nios2/platform
mkdir
upload
Name
Size
Mode
Actions
Kconfig.platform
4478
0644
edit
dl
rm
Makefile
60
0644
edit
dl
rm
Edit:
/usr/src/linux-headers-5.15.0-190/arch/nios2/platform/Kconfig.platform
(4478B)
# SPDX-License-Identifier: GPL-2.0-only menu "Platform options" comment "Memory settings" config NIOS2_MEM_BASE hex "Memory base address" default "0x00000000" help This is the physical address of the memory that the kernel will run from. This address is used to link the kernel and setup initial memory management. You should take the raw memory address without any MMU or cache bits set. Please not that this address is used directly so you have to manually do address translation if it's connected to a bridge. comment "Device tree" config NIOS2_DTB_AT_PHYS_ADDR bool "DTB at physical address" help When enabled you can select a physical address to load the dtb from. Normally this address is passed by a bootloader such as u-boot but using this you can use a devicetree without a bootloader. This way you can store a devicetree in NOR flash or an onchip rom. Please note that this address is used directly so you have to manually do address translation if it's connected to a bridge. Also take into account that when using an MMU you'd have to ad 0xC0000000 to your address config NIOS2_DTB_PHYS_ADDR hex "DTB Address" depends on NIOS2_DTB_AT_PHYS_ADDR default "0xC0000000" help Physical address of a dtb blob. config NIOS2_DTB_SOURCE_BOOL bool "Compile and link device tree into kernel image" depends on !COMPILE_TEST help This allows you to specify a dts (device tree source) file which will be compiled and linked into the kernel image. config NIOS2_DTB_SOURCE string "Device tree source file" depends on NIOS2_DTB_SOURCE_BOOL default "" help Absolute path to the device tree source (dts) file describing your system. comment "Nios II instructions" config NIOS2_ARCH_REVISION int "Select Nios II architecture revision" range 1 2 default 1 help Select between Nios II R1 and Nios II R2 . The architectures are binary incompatible. Default is R1 . config NIOS2_HW_MUL_SUPPORT bool "Enable MUL instruction" help Set to true if you configured the Nios II to include the MUL instruction. This will enable the -mhw-mul compiler flag. config NIOS2_HW_MULX_SUPPORT bool "Enable MULX instruction" help Set to true if you configured the Nios II to include the MULX instruction. Enables the -mhw-mulx compiler flag. config NIOS2_HW_DIV_SUPPORT bool "Enable DIV instruction" help Set to true if you configured the Nios II to include the DIV instruction. Enables the -mhw-div compiler flag. config NIOS2_BMX_SUPPORT bool "Enable BMX instructions" depends on NIOS2_ARCH_REVISION = 2 help Set to true if you configured the Nios II R2 to include the BMX Bit Manipulation Extension instructions. Enables the -mbmx compiler flag. config NIOS2_CDX_SUPPORT bool "Enable CDX instructions" depends on NIOS2_ARCH_REVISION = 2 help Set to true if you configured the Nios II R2 to include the CDX Bit Manipulation Extension instructions. Enables the -mcdx compiler flag. config NIOS2_FPU_SUPPORT bool "Custom floating point instr support" help Enables the -mcustom-fpu-cfg=60-1 compiler flag. config NIOS2_CI_SWAB_SUPPORT bool "Byteswap custom instruction" help Use the byteswap (endian converter) Nios II custom instruction provided by Altera and which can be enabled in QSYS builder. This accelerates endian conversions in the kernel (e.g. ntohs). config NIOS2_CI_SWAB_NO int "Byteswap custom instruction number" if NIOS2_CI_SWAB_SUPPORT default 0 help Number of the instruction as configured in QSYS Builder. comment "Cache settings" config CUSTOM_CACHE_SETTINGS bool "Custom cache settings" help This option allows you to tweak the cache settings used during early boot (where the information from device tree is not yet available). There should be no reason to change these values. Linux will work perfectly fine, even if the Nios II is configured with smaller caches. Say N here unless you know what you are doing. config NIOS2_DCACHE_SIZE hex "D-Cache size" if CUSTOM_CACHE_SETTINGS range 0x200 0x10000 default "0x800" help Maximum possible data cache size. config NIOS2_DCACHE_LINE_SIZE hex "D-Cache line size" if CUSTOM_CACHE_SETTINGS range 0x10 0x20 default "0x20" help Minimum possible data cache line size. config NIOS2_ICACHE_SIZE hex "I-Cache size" if CUSTOM_CACHE_SETTINGS range 0x200 0x10000 default "0x1000" help Maximum possible instruction cache size. endmenu
Save
cmd:
run