/
usr
/
src
/
linux-headers-5.15.0-190
/
drivers
/
net
/
ethernet
/
hisilicon
/
/usr/src/linux-headers-5.15.0-190/drivers/net/ethernet/hisilicon
mkdir
upload
Name
Size
Mode
Actions
hns/
-
0755
rm
hns3/
-
0755
rm
Kconfig
4275
0644
edit
dl
rm
Makefile
309
0644
edit
dl
rm
Edit:
/usr/src/linux-headers-5.15.0-190/drivers/net/ethernet/hisilicon/Kconfig
(4275B)
# SPDX-License-Identifier: GPL-2.0-only # # HISILICON device configuration # config NET_VENDOR_HISILICON bool "Hisilicon devices" default y depends on OF || ACPI depends on ARM || ARM64 || COMPILE_TEST help If you have a network (Ethernet) card belonging to this class, say Y. Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about Hisilicon devices. If you say Y, you will be asked for your specific card in the following questions. if NET_VENDOR_HISILICON config HIX5HD2_GMAC tristate "Hisilicon HIX5HD2 Family Network Device Support" select PHYLIB help This selects the hix5hd2 mac family network device. config HISI_FEMAC tristate "Hisilicon Fast Ethernet MAC device support" depends on HAS_IOMEM select PHYLIB select RESET_CONTROLLER help This selects the Hisilicon Fast Ethernet MAC device(FEMAC). The FEMAC receives and transmits data over Ethernet ports at 10/100 Mbps in full-duplex or half-duplex mode. The FEMAC exchanges data with the CPU, and supports the energy efficient Ethernet (EEE). config HIP04_ETH tristate "HISILICON P04 Ethernet support" depends on HAS_IOMEM # For MFD_SYSCON select MARVELL_PHY select MFD_SYSCON select HNS_MDIO help If you wish to compile a kernel for a hardware with hisilicon p04 SoC and want to use the internal ethernet then you should answer Y to this. config HI13X1_GMAC bool "Hisilicon HI13X1 Network Device Support" depends on HIP04_ETH help If you wish to compile a kernel for a hardware with hisilicon hi13x1_gamc then you should answer Y to this. This makes this driver suitable for use on certain boards such as the HI13X1. If you are unsure, say N. config HNS_MDIO tristate select PHYLIB help This selects the HNS MDIO support. It is needed by HNS_DSAF to access the PHY config HNS tristate help This selects the framework support for Hisilicon Network Subsystem. It is needed by any driver which provides HNS acceleration engine or make use of the engine config HNS_DSAF tristate "Hisilicon HNS DSAF device Support" select HNS select HNS_MDIO help This selects the DSAF (Distributed System Area Frabric) network acceleration engine support. The engine is used in Hisilicon hip05, Hi1610 and further ICT SoC config HNS_ENET tristate "Hisilicon HNS Ethernet Device Support" select PHYLIB select HNS help This selects the general ethernet driver for HNS. This module make use of any HNS AE driver, such as HNS_DSAF config HNS3 tristate "Hisilicon Network Subsystem Support HNS3 (Framework)" depends on PCI select NET_DEVLINK select PAGE_POOL help This selects the framework support for Hisilicon Network Subsystem 3. This layer facilitates clients like ENET, RoCE and user-space ethernet drivers(like ODP)to register with HNAE devices and their associated operations. if HNS3 config HNS3_HCLGE tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support" default m depends on PCI_MSI depends on PTP_1588_CLOCK_OPTIONAL help This selects the HNS3_HCLGE network acceleration engine & its hardware compatibility layer. The engine would be used in Hisilicon hip08 family of SoCs and further upcoming SoCs. config HNS3_DCB bool "Hisilicon HNS3 Data Center Bridge Support" default n depends on HNS3_HCLGE && DCB help Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver. If unsure, say N. config HNS3_HCLGEVF tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support" depends on PCI_MSI depends on HNS3_HCLGE help This selects the HNS3 VF drivers network acceleration engine & its hardware compatibility layer. The engine would be used in Hisilicon hip08 family of SoCs and further upcoming SoCs. config HNS3_ENET tristate "Hisilicon HNS3 Ethernet Device Support" default m depends on 64BIT && PCI depends on INET select DIMLIB help This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08 family of SoCs. This module depends upon HNAE3 driver to access the HNAE3 devices and their associated operations. endif #HNS3 endif # NET_VENDOR_HISILICON
Save
cmd:
run