/
usr
/
src
/
linux-headers-5.15.0-190
/
drivers
/
net
/
ethernet
/
marvell
/
/usr/src/linux-headers-5.15.0-190/drivers/net/ethernet/marvell
mkdir
upload
Name
Size
Mode
Actions
mvpp2/
-
0755
rm
octeontx2/
-
0755
rm
prestera/
-
0755
rm
Kconfig
5732
0644
edit
dl
rm
Makefile
401
0644
edit
dl
rm
Edit:
/usr/src/linux-headers-5.15.0-190/drivers/net/ethernet/marvell/Kconfig
(5732B)
# SPDX-License-Identifier: GPL-2.0-only # # Marvell device configuration # config NET_VENDOR_MARVELL bool "Marvell devices" default y depends on PCI || CPU_PXA168 || PPC32 || PLAT_ORION || INET || COMPILE_TEST help If you have a network (Ethernet) card belonging to this class, say Y. Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about Marvell devices. If you say Y, you will be asked for your specific card in the following questions. if NET_VENDOR_MARVELL config MV643XX_ETH tristate "Marvell Discovery (643XX) and Orion ethernet support" depends on PPC32 || PLAT_ORION || COMPILE_TEST depends on INET select PHYLIB select MVMDIO help This driver supports the gigabit ethernet MACs in the Marvell Discovery PPC/MIPS chipset family (MV643XX) and in the Marvell Orion ARM SoC family. Some boards that use the Discovery chipset are the Momenco Ocelot C and Jaguar ATX and Pegasos II. config MVMDIO tristate "Marvell MDIO interface support" depends on HAS_IOMEM select PHYLIB help This driver supports the MDIO interface found in the network interface units of the Marvell EBU SoCs (Kirkwood, Orion5x, Dove, Armada 370 and Armada XP). This driver is used by the MV643XX_ETH and MVNETA drivers. config MVNETA_BM_ENABLE tristate "Marvell Armada 38x/XP network interface BM support" depends on MVNETA depends on !64BIT help This driver supports auxiliary block of the network interface units in the Marvell ARMADA XP and ARMADA 38x SoC family, which is called buffer manager. This driver, when enabled, strictly cooperates with mvneta driver and is common for all network ports of the devices, even for Armada 370 SoC, which doesn't support hardware buffer management. config MVNETA tristate "Marvell Armada 370/38x/XP/37xx network interface support" depends on ARCH_MVEBU || COMPILE_TEST select MVMDIO select PHYLINK select PAGE_POOL help This driver supports the network interface units in the Marvell ARMADA XP, ARMADA 370, ARMADA 38x and ARMADA 37xx SoC family. Note that this driver is distinct from the mv643xx_eth driver, which should be used for the older Marvell SoCs (Dove, Orion, Discovery, Kirkwood). config MVNETA_BM tristate depends on !64BIT default y if MVNETA=y && MVNETA_BM_ENABLE!=n default MVNETA_BM_ENABLE select HWBM select GENERIC_ALLOCATOR help MVNETA_BM must not be 'm' if MVNETA=y, so this symbol ensures that all dependencies are met. config MVPP2 tristate "Marvell Armada 375/7K/8K network interface support" depends on ARCH_MVEBU || COMPILE_TEST select MVMDIO select PHYLINK select PAGE_POOL help This driver supports the network interface units in the Marvell ARMADA 375, 7K and 8K SoCs. config MVPP2_PTP bool "Marvell Armada 8K Enable PTP support" depends on (PTP_1588_CLOCK = y && MVPP2 = y) || \ (PTP_1588_CLOCK && MVPP2 = m) config PXA168_ETH tristate "Marvell pxa168 ethernet support" depends on HAS_IOMEM depends on CPU_PXA168 || ARCH_BERLIN || COMPILE_TEST select PHYLIB help This driver supports the pxa168 Ethernet ports. To compile this driver as a module, choose M here. The module will be called pxa168_eth. config SKGE tristate "Marvell Yukon Gigabit Ethernet support" depends on PCI select CRC32 help This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx and related Gigabit Ethernet adapters. It is a new smaller driver with better performance and more complete ethtool support. It does not support the link failover and network management features that "portable" vendor supplied sk98lin driver does. This driver supports adapters based on the original Yukon chipset: Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T, Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872. It does not support the newer Yukon2 chipset: a separate driver, sky2, is provided for these adapters. To compile this driver as a module, choose M here: the module will be called skge. This is recommended. config SKGE_DEBUG bool "Debugging interface" depends on SKGE && DEBUG_FS help This option adds the ability to dump driver state for debugging. The file /sys/kernel/debug/skge/ethX displays the state of the internal transmit and receive rings. If unsure, say N. config SKGE_GENESIS bool "Support for older SysKonnect Genesis boards" depends on SKGE help This enables support for the older and uncommon SysKonnect Genesis chips, which support MII via an external transceiver, instead of an internal one. Disabling this option will save some memory by making code smaller. If unsure say Y. config SKY2 tristate "Marvell Yukon 2 support" depends on PCI select CRC32 help This driver supports Gigabit Ethernet adapters based on the Marvell Yukon 2 chipset: Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/ 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21 There is companion driver for the older Marvell Yukon and SysKonnect Genesis based adapters: skge. To compile this driver as a module, choose M here: the module will be called sky2. This is recommended. config SKY2_DEBUG bool "Debugging interface" depends on SKY2 && DEBUG_FS help This option adds the ability to dump driver state for debugging. The file /sys/kernel/debug/sky2/ethX displays the state of the internal transmit and receive rings. If unsure, say N. source "drivers/net/ethernet/marvell/octeontx2/Kconfig" source "drivers/net/ethernet/marvell/prestera/Kconfig" endif # NET_VENDOR_MARVELL
Save
cmd:
run